Part Image

AM26LV31EIDR - Texas Instruments

Description: Low-Voltage High-Speed Quadruple Differential Line Driver With +/-15-kV IEC ESD Protection

Download AM26LV31EIDR Model
Schematic
symbols
Schematic symbol is unavailable for download
PCB
footprints
PCB footprint is unavailable for download
3D
models
3D model is unavailable for download
PCB Footprints
AM26LV31EIDR - Texas Instruments PCB footprint - Small Outline Packages - Small Outline Packages - D (R-PDSO-G16)
click to zoom
3D Models
AM26LV31EIDR - Texas Instruments  - 3D model - Small Outline Packages - D (R-PDSO-G16)
click to zoom

AM26LV31EIDR Details

  • Manufacturer Part Number:

    AM26LV31EIDR

  • Brand Name:

    Texas Instruments

  • Pbfree Code:

    Yes

  • Rohs Code:

    Yes

  • Part Life Cycle Code:

    Active

  • Part Package Code:

    SOIC

  • Package Description:

    SOIC-16

  • Pin Count:

    16

  • Country Of Origin:

    Malaysia, Mexico

  • ECCN Code:

    EAR99

  • HTS Code:

    8542.39.00.90

  • Manufacturer:

    Texas Instruments

  • YTEOL:

    15

  • Additional Feature:

    BUILT-IN DRIVER OUTPUT SHORT CIRCUIT PROTECTION

  • Differential Output:

    YES

  • Driver Number of Bits:

    4

  • Input Characteristics:

    STANDARD

  • Interface IC Type:

    LINE DRIVER

  • Interface Standard:

    EIA-422-B; TIA-422-B; V.11

  • JESD-30 Code:

    R-PDSO-G16

  • JESD-609 Code:

    e4

  • Length:

    9.9 mm

  • Moisture Sensitivity Level:

    1

  • Number of Functions:

    4

  • Number of Terminals:

    16

  • Operating Temperature-Max:

    85 °C

  • Operating Temperature-Min:

    -40 °C

  • Out Swing-Min:

    2 V

  • Output Characteristics:

    3-STATE

  • Output Low Current-Max:

    0.03 A

  • Output Polarity:

    TRUE

  • Package Body Material:

    PLASTIC/EPOXY

  • Package Code:

    SOP

  • Package Equivalence Code:

    SOP16,.25

  • Package Shape:

    RECTANGULAR

  • Package Style:

    SMALL OUTLINE

  • Peak Reflow Temperature (Cel):

    260

  • Qualification Status:

    Not Qualified

  • Seated Height-Max:

    1.75 mm

  • Supply Current-Max:

    0.1 mA

  • Supply Voltage-Max:

    3.6 V

  • Supply Voltage-Min:

    3 V

  • Supply Voltage-Nom:

    3.3 V

  • Supply Voltage1-Max:

    3.6 V

  • Supply Voltage1-Min:

    3 V

  • Supply Voltage1-Nom:

    3.3 V

  • Surface Mount:

    YES

  • Technology:

    BICMOS

  • Temperature Grade:

    INDUSTRIAL

  • Terminal Finish:

    Nickel/Palladium/Gold (Ni/Pd/Au)

  • Terminal Form:

    GULL WING

  • Terminal Pitch:

    1.27 mm

  • Terminal Position:

    DUAL

  • Time@Peak Reflow Temperature-Max (s):

    30

  • Transmit Delay-Max:

    12 ns

  • Width:

    3.9 mm

AM26LV31EIDR Frequently Asked Questions (FAQs)

  • A good PCB layout practice is to keep the analog and digital grounds separate, use a solid ground plane, and keep the signal traces short and away from noise sources. TI also recommends following the layout guidelines in the application note SLVAE03.
  • Proper termination is critical for high-speed data transmission. TI recommends using a 100-ohm differential termination resistor at the receiver end, and a 50-ohm single-ended termination resistor at the transmitter end. Additionally, ensure that the transmission line impedance is matched to the device's output impedance.
  • The maximum cable length supported by the AM26LV31EIDR depends on the data rate and cable characteristics. As a general guideline, TI recommends keeping the cable length below 10 meters for data rates up to 100 Mbps, and below 5 meters for data rates above 100 Mbps.
  • The AM26LV31EIDR has built-in hot swap protection, but it's still important to follow proper hot swap procedures to prevent damage to the device. TI recommends using a hot swap controller or a power switch with overcurrent protection to ensure safe insertion and removal of the device.
  • TI recommends powering up the device in the following sequence: VCC, then VCCIO, and finally the input signals. Power down in the reverse sequence to prevent damage to the device.

Trust Checks

This model has been provided by community users.
Community Provided
This model has been verified by system checks.
System Verified
This model has been reviewed by community users.
Community Approved
Sponsored

AM26LV31EIDR Overview

Use the download button to access the AM26LV31EIDR schematic symbol, PCB footprint, and 3D model.
To find more CAD model downloads similar to this part, try a partial part number search, like AM26L, or try a keyword search, such as Line Driver or Receivers

About Texas Instruments

Texas Instruments (TI) designs and manufactures semiconductors and integrated circuits for a wide range of applications. The company's product portfolio includes analog chips, which are essential for managing power and signal functions in electronic devices, and embedded processors, which serve as the brains in various systems, enabling functionality in everything from industrial equipment to consumer electronics. TI's innovations in semiconductor technology have made it a leader in the industry.

Parts related to AM26LV31EIDR

Showing 0 results

AM26LV31EIDR Alternates

Showing results

Image Part Number Model
Part Image AM26LV31CDR Texas Instruments

Line Driver, 4 Func, 4 Driver, BICMOS, PDSO16

Part Image DS26LV31TM/NOPB National Semiconductor Corporation

Line Driver, 4 Func, 4 Driver, CMOS, PDSO16

Part Image AM26LV31CDE4 Texas Instruments

Line Driver, 4 Func, 4 Driver, BICMOS, PDSO16

Part Image AM26LV31IDRE4 Texas Instruments

Line Driver, 4 Func, 4 Driver, BICMOS, PDSO16

Part Image AM26LV31IDRG4 Texas Instruments

Line Driver, 4 Func, 4 Driver, BICMOS, PDSO16

For a full list of alternate parts for AM26LV31EIDR, check out Findchips.com